Viewsonic Pro8200 Projector – Physical Tour

Viewsonic Pro8200 Projector - Appearance

As is typical, there’s a front infra-red sensor for the Pro8200 projector’s remote control. The control panel (more below) is on the top, towards the back right (looking from the rear). Venting is out the side, while inputs and other connectors are in the back. There’s also a security bar, and a Kensington lock slot.

Underneath, there is an adjustable, drop down, center front foot, and both rear feet are screw thread adjustable.

Size of the Viewsonic Pro8200 projector has to be considered small. True, there are other single chip DLP projectors for home that are smaller, but, most LCD and LCoS projectors are a size or two larger.

Unlike home theater projectors in general, the Pro8200, as mentioned above, is a cross-over projector. It is designed to do double duty, as a home theater projector. It claims 2000 lumens, which is a healthy amount of lumens for a sub-$1000 business projector (yes some are up to 3500 lumens, etc, but 2000 – 2500 lumens has been the standard for basic portable projectors for several years now.

And the Viewsonic Pro8200 has a speaker – considered a necessity for business and education projectors.

Pro8200 Control Panel

The Viewsonic Pro8200 projector’s control panel is on the top, towards the rear (and the right side, if looking from the back). It’s a pretty standard affair, with the power switch off to the top left. (once for on, twice for off).

There are indicator lamps for Temp and Lamp. The rest of the control panel consists of your normal four navigation arrows in a roundconfiguration,but with the center button doubling as both Menu, and (menu) Exit. The up and down arrows double as keystone correction controls (when not in the Menu mode). It should be noted, that the projector does offer an auto-keystone adjust as well.

There are two additional controls, large curved buttons outside of the right and down arrows. The one to the right is the Enter button, and the one on the bottom – is the Source select. (The Pro8200 also offers auto source selection – it will find the first available source, if you set it that way.)

All considered, the control panel works very nicely. In this case, I like the center Menu button, whereas most projectors have the menu button outside the navigation ring, and it could be almost anywhere.

Click Image to Enlarge

Pro8200 Projector - Input/Output

Talk about well equipped, but you have to expect that when this is a cross-over projector as it needs the selection of inputs and connectors to survive in both the home entertainment world, and in a business or education environment as well.

Looking at the back of the Pro8200 by Viewsonic, and starting at the left, you’ll find an RS-232 for command and control. Next to it, the computer inputs – 2 – standard “vga” HD15 connectors, labeled Computer 1, and 2. Also there is a Monitor Out, very handy when working with a desktop, or if you need a second display, in general.

Click Image to Enlarge

Next comes a component video input (three color coded RCA jacks – Red, Green, and Blue). Right next store to those, are the composite video jack (yellow RCA) and a pair of audio inputs (left and right – white and red RCA jacks, plus an S-video connector.

Audio, not normally found on home projectors is a big thing for the Viewsonic Pro8200. Not only is there a rather decent sounding speaker, that can handle, say, a classroom, or provide decent sound to a movie in a pinch, but a lot of audio inputs and outputs. In addition to the two mentioned, there are two additional audio inputs (each a stereo mini-connector) and an audio out. Plus there’s even a Mic input (more on that later), and a 12 volt trigger for controlling a properly equipped screen.

That leaves only a USB A, and of course, a pair of HDMI 1.3 inputs. That’s a pretty complete and respectable set of inputs and outputs.

Now that we’ve gotton to the HDMI inputs, here’s where we had big problems with the first, pre-production projector. It hated long cables, It refused to work with my PS3 or a Magnavox – with any of several hdmi cables in the 4 to 8 meter lengths. It fared only slightly better with the Magnavox, which at least was clean with a 2 meter cable. From the PS3 even that was problematic. End of conversation, between the hdmi, and the ghosts – static with the power off (the mic input), the first projector had issues.

The good news is that the newer one had virtually no trouble, where the first one was a complete disaster. There was still one longer HDMI cable that it wouldn’t work with, that three other projectors had no trouble with, but overall, let’s say there’s no major hdmi issue, although the Pro8200 may be more finicky about cabling than some others.